Product Details:
Payment & Shipping Terms:
|
| Other Name: | Tact Switch 6x6mm | Switch Rating: | DC 12V, 50mA |
|---|---|---|---|
| Operation Temperature Range: | - 20℃~ + 70℃ | Contact Resistance: | Max. 100mΩ |
| IP-protection: | IP 40 | Switch Action: | Push-on Type, S.P.S.T. |
| High Light: | smd chip resistor,pir motion sensor |
||
6*6mm waterproof tactile switch with copper pin, height from 4.3 ~ 31mm
Description:
• Different heights are available
• Design 6*6mm
• Solder terminals
Tact switch is an on/off electronic switch that is only on when the button is pressed or if there is a definitive change in pressure. Another way to consider it, as momentary make or brake switch. As soon as a tact switches button is released, the circuit is broken.
You can choose between gold or silver contact material and you can choose from multiple cap options for certain models.
Application:
We offer multiple sizes, operating forces, actuator heights, and life cycles to meet the needs of your application. Our tact switches are used for human interface applications where the user applies force to the push button momentary switch for selection and control. Include telecommunications, consumer electronics, audio/visual, medical device, testing/instrumentation, computer peripherals and more.
Unique selling proposition:
• Reliable tactile feedback on input
• Simple assembly
• Long life time
Mechanical data:
| Actuating force | 1.6±0.5N |
| Actuating travel | 0.25+0.2 / -0.1mm |
| End stop strength | 50N / 3S |
| Life time | >100000 actuations |
Soldering data:
| Soldering methods | Reflow |
| Solderability | 245℃ / 5 sec (IEC 60068-2-58 test td) |
| Resistance to soldering heat | 260℃ / 10 sec (IEC 60068-2-58 test td) |
| Item | Test condition | Performance |
| Cold test |
1.Temperature:-30±2 ℃ 2.Duration of test: 96h 3.Take off a drop water 4.Standard conditions after test: 1h |
Contact resistance 200mΩ max. Shall be satisfied |
| Heat test |
1.Temperature: 80±2 ℃ 2.Duration of test: 96h 3.Standard conditions after test: 1h |
Contact resistance 200mΩ max. Shall be satisfied |
| Temperature cycle |
1.Test cycle: 5 cycles 2.Standard confition after test:1h |
Contact resistance 200mΩ max. Shall be satisfied |
| Humidity test |
1.Temperature: 60±2 ℃ 2.Relative humidity: 90-95% 3.Duration of test: 96h 4.Take off a drop water 5.Standard conditions after test:1h |
Contact resistance 200mΩ max. Shall be satisfied |
| Salt mist | The switch shall be subjected to a fime mist f salt solution at a temperature of 35±2 ℃ for 24h continuously(salt solution concentration 5±1% by weight) |
Without excessive rust. Contact resistance 200mΩ max |
| Endurance(switching) action |
1.D.C.12V 50mA resistance load 2.Operation speed: 2-3 times/sec. 3.Push force: Maximum value operation force 4.Operation number: 50,000 times |
Contact resistance 200mΩ max. Bouncing: 10ms max. Variation rate of operation force shall be within ±30% to the value before testing |
| Withstand H2S |
1.Density:3±1ppm 2.Temperature: 40±2 ℃ 3.Relative humidity: 90-95% 4.Duration of test: 24h 5.Standard condition after test: 1h |
Contact resistance 200mΩ max. Shall be satisfied |
| Withstand SO2 |
1.Density:10±2ppm 2.Temperature: 40±2 ℃ 3.Relative humidity: 90-95% 4.Duration of test: 24h 5.Standard condition after test:1h |
Contact resistance 200mΩ max. Shall be satisfied |
| Shock |
Measure after test at a condition below peak acceleration---80G Test time-6 directions, each 3 times total 18 times |
Contact resistance 200mΩ max. Shall be satisfied |
| L | 4.3 | 4.5 | 5 | 5.5 | 6 | 6.5 |
| 7 | 7.5 | 8 | 8.5 | 9 | 9.5 | 10 |
| 10.5 | 11 | 11.5 | 12 | 13 | 14 | 15 |
| 16 | 17 | 17.5 | 18 | 19 | 20 | 21 |
| 22 | 23 | 24 | 25 | 26 | 31mm | |
Contact Person: Mr. Roy Zhang
Tel: 86 574 56807757
Fax: 86-574-55844980
